Page 2 of 2
Posted: Wed Jun 15, 2005 5:19 am
by AndreD
On 2005-06-15 06:11, jea wrote:
Then I read something on the rme tech site, that the new mainboards had problems, making a glitch every x minute.
That was my first thought too but the test changed my mind...
Now, I´m working at 4ms latency without any glitch or crackle
Posted: Wed Jun 15, 2005 5:29 am
by jea
Are you using the Intel D925XCV?
Posted: Wed Jun 15, 2005 5:31 am
by AndreD
no, I´m using the ASUS P5AD2-E with the same chipset...
Posted: Wed Jun 15, 2005 5:32 am
by jea
I might add, I only did the tests.
Realworld might be, lets say, a b i t different!
Posted: Wed Jun 15, 2005 5:35 am
by jea
Ok.
I might give the card another try, without Scope. I think I perhaps would be better using a dedicated pc for my Scope, then use Wormhole or Teleport or ADAT for getting scope things into main DAW.
Posted: Wed Jun 15, 2005 5:39 am
by AndreD
scope works good as rme.. the problem doas´nt originates on this site...
Posted: Thu Jun 16, 2005 12:13 pm
by jea
Hi,
I meant it could be wise if this had worked,
one way or another.
Posted: Fri Jul 01, 2005 10:17 pm
by firubbi
@AndreD im interested to make the same setup. Can you tell more about your setup?
1) mobo is ok.
2) Processor- which one?
3) RAM- is it kingstone? Did you install 2GB ram?
4) VGA is ok
5) Hard disk- why you select Parallel ATA? Isn’t it SATA is better for audio?
thanks
Posted: Sat Jul 02, 2005 10:35 am
by AndreD
OK:
ASUS P5 AD2 E Premium
1 GB RAM (2x Samsung DDR2 512)
MATROX P650 (PCI-E!!)
SATA Samsung SpinPoint
Hyperthreading, ACPI
Intel P4 775 3.2 GHz
Don´t use the N.O.S software overclocking feature!
Posted: Sat Jul 02, 2005 10:36 am
by AndreD
On 2005-06-15 06:29, jea wrote:
Are you using the Intel D925XCV?
Are you using the NOS overclocking software?
I noticed some promblems while using it togerhter with nuendo, better turne it off...
<font size=-1>[ This Message was edited by: AndreD on 2005-07-02 13:42 ]</font>
Posted: Mon Jul 18, 2005 12:47 pm
by jea
No, I´m not overclocking any.
But I have ordered Matrox P650, it should have been here today, but it is delayed.
So I am going to test again.
After all, this is the best cpu I have!
I am however more and more considering putting my Scope Pro, 2x Pulsar II in a separate pc, just to make the environment perfect for them, then I have 27DSP´s....
I´m wondering of getting the breakoutbox for my Luna II, and put that in the main DAW.
I basically need 10 i/o.
Not sure however ....
Well some testing will tell.
Posted: Fri Sep 30, 2005 5:56 pm
by tripstation
Hi,
Anyone used CT-479 pentium4 mobile adapter on any of these boards with scope cards?
Asus P4GD1
Asus P4GPL-X
regards,
Jim
Posted: Sun Oct 02, 2005 8:50 pm
by wayne
On 2005-06-15 06:31, AndreD wrote:
no, I´m using the ASUS P5AD2-E with the same chipset...
My understanding was that it's a different chipset Andre - 925X
E on the ASUS.
Posted: Thu Mar 30, 2006 10:41 am
by Artvader
I have a Pulsar 2 and a Scope board. When I used these boards with Abit IC7-MAX3, I encountered a problem when I used the USB 2 ports. The system just hang.
Now I am gonna use a Asus P5WD2 Premium motherboard. Are there any out there that know about any known problems around this?
Posted: Thu Mar 30, 2006 10:53 am
by ali
Posted: Sun Apr 02, 2006 3:34 am
by H-Rave
This may be of some interest.
http://www.steinberg.de/fileadmin/redak ... h_Info.pdf
I saw a table of processors somewhere,but I can't for the hell of me remember where it was.