This thread is where you list the full specs of your machine that successfully runs your Creamware hardware. Please, no questions here (start a new thread), just setups that follow a similiar format as below.
Here's my current one which I got in October01. I'll update this when I get around to upgrading, but it's doing great for me right now.
4U Black 19" Rackmount Case
ASUS P4TE i850 Motherboard (ICS version)
1.8Ghz Pentium 4
512meg (2x256) Samsung PC800 RDRAM
80gig 7200RPM Seagate Barracuda IV
32meg Matrox G450 Dual Head
22" Black Trinitron Monitor @ 1600x1200x32
24X Teac CDRW (Black)
16X Pioneer DVD-ROM Slot Load (Black)
350 watt Enermax Whisper (Fan Control) Power Supply
WinME/WinXP Dual Boot (tweaked)
SCOPE/SP+PowerPulsar (30DSP - SCOPE Fusion Platform V3.1a)
Logic 5.13 SOON
SubMasterVerbTest - 10 masterVerbs (at
default BIOS settings)
I'll upgrade to Logic 5, and put in a Northwood 533mhz FSB chip in the next few months... but rock solid and fast system, it's been good to me.
_________________
<a href=http://infinitevortex.com>Infinite Vortex Audio</a>
<font size=-1>[ This Message was edited by: subhuman on 2002-04-22 09:44 ]</font>
<font size=-1>[ This Message was edited by: subhuman on 2002-05-03 14:27 ]</font>
<font size=-1>[ This Message was edited by: subhuman on 2002-05-30 09:03 ]</font>
Creamware User Setups
4U Blue 19" Rackmount Case (both machines)
ASUS P4B266 Motherboard
1.6AGhz Pentium 4 @ 2130 with Alpha heatsink/homemade duct (quiet)
512meg (2x256) Crucial DDR
80gig 7200RPM Seagate Barracuda IV
32meg Matrox G400 Dual Head
2x 19" Blue Lacie ElectronBlue Monitors (diamondtron)
Cheap old and Quiet 12x Cdrom drive
(Just for samples, burner on other machine)
430 watt Enermax Whisper (Fan Control) Power Supply
WinME (tweaked)
SCOPE/DP+Pulsar1 (running Pulsar V3.01b and ScopeDP)
Dlink NIC
Pulsar on slot 1, Scope on slot 5, IRQ5 forced in BIOS
OASYS in other machine ADAT <> Scope
Acid pro 3.0
Sound forge 5
Logic 4.6
Orion Pro
Fruityloops 3.x pro
<font size=-1>[ This Message was edited by: defex on 2002-04-17 20:07 ]</font>
ASUS P4B266 Motherboard
1.6AGhz Pentium 4 @ 2130 with Alpha heatsink/homemade duct (quiet)
512meg (2x256) Crucial DDR
80gig 7200RPM Seagate Barracuda IV
32meg Matrox G400 Dual Head
2x 19" Blue Lacie ElectronBlue Monitors (diamondtron)
Cheap old and Quiet 12x Cdrom drive
(Just for samples, burner on other machine)
430 watt Enermax Whisper (Fan Control) Power Supply
WinME (tweaked)
SCOPE/DP+Pulsar1 (running Pulsar V3.01b and ScopeDP)
Dlink NIC
Pulsar on slot 1, Scope on slot 5, IRQ5 forced in BIOS
OASYS in other machine ADAT <> Scope
Acid pro 3.0
Sound forge 5
Logic 4.6
Orion Pro
Fruityloops 3.x pro
<font size=-1>[ This Message was edited by: defex on 2002-04-17 20:07 ]</font>
You can see a (up2date)list of my current hard-/software @ http://d-media.dk/studio.htm
Kim.
The PC's are in another room. Very effective NoizeControl
<font size=-1>[ This Message was edited by: kimgr on 2003-06-30 01:23 ]</font>
Kim.
The PC's are in another room. Very effective NoizeControl
<font size=-1>[ This Message was edited by: kimgr on 2003-06-30 01:23 ]</font>
ASUS P4b266 (no onboard audio or LAN)
1.8GHz P4 with 512K L2 cache
Matrox 550
1Gb DDR SDRAM
Seagate Bararcuda IV 40Gb (primary master)
Seagate Bararcuda IV 80Gb (secondary master)
Iomega 32x10x40 CDRW (primary slave)
Iomega 100Mb ZIP on USB (no problems)
Dual 19-inch CRT monitors
450w power
PulsarII
Osprey210 analog capture card
Windows XP home
AcidPro 4
SoundForge 6
NI Kontakt
VegasVideo 3
FL Studio 4
Orion Platinum
Absynth
Z3ta+
Plasticz
Photoshop 5.5
Illustrator 9
Fireworks MX
Dreamweaver MX
Flash MX
Winzip 8
+ surviving scraps of hardware: SPX90, EPS16, MU80
<i>Obviously not a 100% dedicated DAW, but still get rock solid running</i>
* old pic deleted *
<font size=-1>[ This Message was edited by: spirit on 2003-07-04 09:40 ]</font>
1.8GHz P4 with 512K L2 cache
Matrox 550
1Gb DDR SDRAM
Seagate Bararcuda IV 40Gb (primary master)
Seagate Bararcuda IV 80Gb (secondary master)
Iomega 32x10x40 CDRW (primary slave)
Iomega 100Mb ZIP on USB (no problems)
Dual 19-inch CRT monitors
450w power
PulsarII
Osprey210 analog capture card
Windows XP home
AcidPro 4
SoundForge 6
NI Kontakt
VegasVideo 3
FL Studio 4
Orion Platinum
Absynth
Z3ta+
Plasticz
Photoshop 5.5
Illustrator 9
Fireworks MX
Dreamweaver MX
Flash MX
Winzip 8
+ surviving scraps of hardware: SPX90, EPS16, MU80
<i>Obviously not a 100% dedicated DAW, but still get rock solid running</i>
* old pic deleted *
<font size=-1>[ This Message was edited by: spirit on 2003-07-04 09:40 ]</font>
Computer Hardware
Asus P4B533, 2533 MHz P4, 512MB DDR 266MHz,
Enermax 450W PSU dual fan,
Matrox G450 32MB dualhead (busmaster disabled) driving two 1024*768 screens,
Seagate Barracuda IV 80GB and 120 GB, Samsung 160GB, all 7200rpm & 8MB cache,
NEC 3500A DVD-RW,
Pulsar2 SRB,
Scope w Z-Link daughterboard,
Firewire pci card,
LAN pci card.
IRQ settings: CW cards on 9, Matrox on 11, onboard audio on 7, LAN on 5. Onboard audio & COM's disabled. I've put the CW boards in slots 2,4 since the onboard audio shares with slots 1,5.
Software
Windows XP Pro, SFP 4
I gave up testing on 16 Masterverbs, apparently on the edge of dsp memory...
System limitation: 90% chance of BSOD upon loading of STS or sample osc, any hints are welcome on that
Other gear
Peavey Pc1600x for Scope and
Behringer BCF2000 for Cubase remote,
RolandJX-1 keyb (no AT):,
Philicorda organ (cheesy as fnck),
CW Luna2496 break-out box,
TEAC 80-8 1/2" 8 track with dbx module,
StudioMaster 16-2 analog mixer,
Focusrite Trak Master pre-amp,
Lab Series L9 guitar amp,
Toshiba Sattelite S2450 running Demudi, with Edirol UA-25 slaved to SFP providing 2 extra pre's,
...
More or less the same can be found on my homepage.
<font size=-1>[ This Message was edited by: at0m on 2006-05-09 16:50 ]</font>
Asus P4B533, 2533 MHz P4, 512MB DDR 266MHz,
Enermax 450W PSU dual fan,
Matrox G450 32MB dualhead (busmaster disabled) driving two 1024*768 screens,
Seagate Barracuda IV 80GB and 120 GB, Samsung 160GB, all 7200rpm & 8MB cache,
NEC 3500A DVD-RW,
Pulsar2 SRB,
Scope w Z-Link daughterboard,
Firewire pci card,
LAN pci card.
IRQ settings: CW cards on 9, Matrox on 11, onboard audio on 7, LAN on 5. Onboard audio & COM's disabled. I've put the CW boards in slots 2,4 since the onboard audio shares with slots 1,5.
Software
Windows XP Pro, SFP 4
I gave up testing on 16 Masterverbs, apparently on the edge of dsp memory...
System limitation: 90% chance of BSOD upon loading of STS or sample osc, any hints are welcome on that
Other gear
Peavey Pc1600x for Scope and
Behringer BCF2000 for Cubase remote,
RolandJX-1 keyb (no AT):,
Philicorda organ (cheesy as fnck),
CW Luna2496 break-out box,
TEAC 80-8 1/2" 8 track with dbx module,
StudioMaster 16-2 analog mixer,
Focusrite Trak Master pre-amp,
Lab Series L9 guitar amp,
Toshiba Sattelite S2450 running Demudi, with Edirol UA-25 slaved to SFP providing 2 extra pre's,
...
More or less the same can be found on my homepage.
<font size=-1>[ This Message was edited by: at0m on 2006-05-09 16:50 ]</font>
I have my Luna II (IRQ 5) and Pulsar II SRB (IRQ 9) running under Windows 98 SE (with Win2k dual-booted for other stuff) with the following hardware:
Abit BE6r2 BX Motherboard (with Highpoint HPT366 IDE controller)
PIII 500 Slot 1 Processor
256MB PC100 RAM
Diamond Viper V330 (Nvidia Riva 128) 4MB graphics adapter (I think)
6.4GB Generic IDE Hard Drive (System disk)
12.5GB IBM Deskstar Hard Drive (Audio disk)
17" Belinea Monitor
3Com Fast EtherLink XL 10/100Mb TX Ethernet NIC (3C905-TX)
USB Disabled
Samsung 32x CDROM
I used to have Yamaha DS2416 and AWE64 Gold cards in there as well, but eventually gave up on trying to integrate them all together. Shame really, as I liked my Yamaha card.
Everything works pretty well now. No problems with performance really. Even the display performance has been good since Luna v2.5 (which I'm still running). Run at 13ms which does fine for me. Can run at 7ms, but seriously reduces the amount of VST stuff I can use.
Currently enjoying Cubase VST32 5.1 which is significantly better in nearly every respect than 3.7. Big fan of Wavelength devices (I've got Transfusion, DubSubII and Plasma).
External Kit: Roland JV2080, KRK K-ROK speakers, Samson Servo-170, Mackie 1202VLZ.
Abit BE6r2 BX Motherboard (with Highpoint HPT366 IDE controller)
PIII 500 Slot 1 Processor
256MB PC100 RAM
Diamond Viper V330 (Nvidia Riva 128) 4MB graphics adapter (I think)
6.4GB Generic IDE Hard Drive (System disk)
12.5GB IBM Deskstar Hard Drive (Audio disk)
17" Belinea Monitor
3Com Fast EtherLink XL 10/100Mb TX Ethernet NIC (3C905-TX)
USB Disabled
Samsung 32x CDROM
I used to have Yamaha DS2416 and AWE64 Gold cards in there as well, but eventually gave up on trying to integrate them all together. Shame really, as I liked my Yamaha card.
Everything works pretty well now. No problems with performance really. Even the display performance has been good since Luna v2.5 (which I'm still running). Run at 13ms which does fine for me. Can run at 7ms, but seriously reduces the amount of VST stuff I can use.
Currently enjoying Cubase VST32 5.1 which is significantly better in nearly every respect than 3.7. Big fan of Wavelength devices (I've got Transfusion, DubSubII and Plasma).
External Kit: Roland JV2080, KRK K-ROK speakers, Samson Servo-170, Mackie 1202VLZ.
wow! super duper cool factor defex. those cases and sliding rack setup musta cost a bundle! that green light emanating from inside makes that hefty case look like something you'd find on a borg cube
heres my meager mac setup which works well for myself. i am running os 8.6 and luna 2.52 on an elektra card, mainly using the modular.
Apple Power Mac 7500/100 running on a wholloping 43mhz system bus!
built-in: networking, narrow scsi2 , serial and adb
G3 300 Sonnet Crescendo (pds) w/ 1meg level 2 cache onboard
192 mb of mixed size interleaved (two identical modules placed in opposing slots) 168pin 60ns 2 or 4k fpm dimm memory modules (generic)
Ixmicro Twin Turbo 128m2 pci video w/ 4mb of vram
4.1 gig Seagate Barracuda 7200rpm narrow scsi2 (main).
9.1 gig Ibm Deskstar 7200rpm narrow scsi2 (audio)
17" Applevision a/v monitor
Yamaha CRW8824s int. scsi burner
Iomega Zip 100 ext. scsi
can't do a masterverb test yet, but if my experience with some of the freeware verbs are any indication, i won't be able to run a single one. i get the pci bus overflow message on ONE instance of these devices. i can't recall the names of them off hand.
aside from this i have had no problems directly related to hardware.
i am cpu strapped for the most part so i run at the highest ulli setting (34ms) at 44/16, it gives me no problems.
externally: motu micro express, sennheiser hd540 phones (no monitors yet, have a nice nad component stereo and some 1970's sansui beaters, with a blown right tweeter), broken esq1 (still plays on occasion some nice presets on a cart i have. plan to get fixed and also can get used for its controllers. serves as a large dust collector mostly
), peavey sp, zoom 1201, lexicon vortex, mackie 1202, 48 point patchbay, minidisc recorder, few mic's, some ethnic percusive instruments, a didj, bontempi organ (want to upgrade to a nicer one, hah!).
most of my stuff is perched on a 72" 3 tier Ultimate A-Frame with 8 arms. i don't reccomend putting a 60 pound monitor on the 3rd tier of anyones keyboard stand if they have any sort of earthquake activity in the area or live in a heavy, industrial part of the city. i just happen to not be, so its not a big concern and it works out really well, just gotta watch it when i'm banging on me keyboard, (when it was functional) as it is a little wobbly.
software wise: digital perfomer 2.72, pluggo 2.1, bias peak 2.58vst, d-sound pro, soundapp, soundhack, thonk, agreiphontes lyre, soundeffects, amadeus II, sp remote, qwerty midi keyboard, instant player, lots of other freeware plugs and softs in rotation.
using oms 2.38 , freemidi 1.44, & motu audio system 2.33.
i am unable to record with the creamware audio driver using any of that software which can be used in a recording manner. it conks out and causes crashing when used as playback only. so i just don't use it, but instead use the built-in a/v features on my mac and soundmanager for non asio apps or when i need to run two audio apps together (only record thru asio and the elektra though), with dp i can route soundmanager internal output into the program itself, for recording.
like spirit my machine is used for any amount of differing thing, gives me no conflicts.
my music is varied and largely unfinished. currently experimenting with found sounds and sparse electroacoustic atmospheres.
<img src="http://webpages.charter.net/amfreq/pics ... .jpg"</img src>
<font size=-1>[ This Message was edited by: castol on 2002-05-14 10:26 ]</font>
heres my meager mac setup which works well for myself. i am running os 8.6 and luna 2.52 on an elektra card, mainly using the modular.
Apple Power Mac 7500/100 running on a wholloping 43mhz system bus!
built-in: networking, narrow scsi2 , serial and adb
G3 300 Sonnet Crescendo (pds) w/ 1meg level 2 cache onboard
192 mb of mixed size interleaved (two identical modules placed in opposing slots) 168pin 60ns 2 or 4k fpm dimm memory modules (generic)
Ixmicro Twin Turbo 128m2 pci video w/ 4mb of vram
4.1 gig Seagate Barracuda 7200rpm narrow scsi2 (main).
9.1 gig Ibm Deskstar 7200rpm narrow scsi2 (audio)
17" Applevision a/v monitor
Yamaha CRW8824s int. scsi burner
Iomega Zip 100 ext. scsi
can't do a masterverb test yet, but if my experience with some of the freeware verbs are any indication, i won't be able to run a single one. i get the pci bus overflow message on ONE instance of these devices. i can't recall the names of them off hand.
aside from this i have had no problems directly related to hardware.
i am cpu strapped for the most part so i run at the highest ulli setting (34ms) at 44/16, it gives me no problems.
externally: motu micro express, sennheiser hd540 phones (no monitors yet, have a nice nad component stereo and some 1970's sansui beaters, with a blown right tweeter), broken esq1 (still plays on occasion some nice presets on a cart i have. plan to get fixed and also can get used for its controllers. serves as a large dust collector mostly
), peavey sp, zoom 1201, lexicon vortex, mackie 1202, 48 point patchbay, minidisc recorder, few mic's, some ethnic percusive instruments, a didj, bontempi organ (want to upgrade to a nicer one, hah!).most of my stuff is perched on a 72" 3 tier Ultimate A-Frame with 8 arms. i don't reccomend putting a 60 pound monitor on the 3rd tier of anyones keyboard stand if they have any sort of earthquake activity in the area or live in a heavy, industrial part of the city. i just happen to not be, so its not a big concern and it works out really well, just gotta watch it when i'm banging on me keyboard, (when it was functional) as it is a little wobbly.
software wise: digital perfomer 2.72, pluggo 2.1, bias peak 2.58vst, d-sound pro, soundapp, soundhack, thonk, agreiphontes lyre, soundeffects, amadeus II, sp remote, qwerty midi keyboard, instant player, lots of other freeware plugs and softs in rotation.
using oms 2.38 , freemidi 1.44, & motu audio system 2.33.
i am unable to record with the creamware audio driver using any of that software which can be used in a recording manner. it conks out and causes crashing when used as playback only. so i just don't use it, but instead use the built-in a/v features on my mac and soundmanager for non asio apps or when i need to run two audio apps together (only record thru asio and the elektra though), with dp i can route soundmanager internal output into the program itself, for recording.
like spirit my machine is used for any amount of differing thing, gives me no conflicts.
my music is varied and largely unfinished. currently experimenting with found sounds and sparse electroacoustic atmospheres.
<img src="http://webpages.charter.net/amfreq/pics ... .jpg"</img src>
<font size=-1>[ This Message was edited by: castol on 2002-05-14 10:26 ]</font>
-
snoopy4ever
- Posts: 367
- Joined: Tue Feb 19, 2002 4:00 pm
- Location: Costa Rica
I have a PulsarII 3.01 running under Windows 98 SE with the following hardware:
BX Motherboard
PIII 550 Slot 1 Processor
384MB PC100 RAM
ATI graphics adapter
6.4GB Generic IDE Hard Drive (System disk)
20 GB Quantum Hard Drive (Programs disk)
40 GB Glyph X-project HardDrive (FireWire)
17" Monitor
No Network, No Internet.
Midiman USB 4x4
Creative 32x CDROM
M-Audio Delta TDIF with analog I/O and SP/DIF I/O
SoundBlaster Live with ASIO Drivers v 1.84
Tascam TM-D1000 Digital Mixer (All Cards I/O installed)
Mackie 1202 Analog Mixer
Yamaha NS-10's, Krk-KRock monitors
old Kawai K1
Yamaha DD50 trigger pads.
ART X-treme Pedal distortion plus effects
Digitech Vocalist EX.
Tascam MKIII cassete rec/player.
Good old electric and acoustic guitars.
Cubase 5.1
WaveLab 3.0
a bunch of Plugins
I use the Delta TDIF as the Recording card, the TM-D1000's effects are real good as well the dynamics, so I use both for my live recordings, the Pulsar is for all the extra processing and sound desing. It's important to say that the Delta TDIF is the master clock on my setup, thus the Pulsar II is the slave as well the TM-D1000, no problems so far.
I keep the Sblive in order to understand DSP, cause the new Drivers allow direct programming for the chip (emu10k1), I'm a software engineer so I want to lear that stuff, who knows,,may be some day I can program my own effects...
.
<font size=-1>[ This Message was edited by: snoopy4ever on 2002-04-19 11:55 ]</font>
<font size=-1>[ This Message was edited by: snoopy4ever on 2002-04-19 11:55 ]</font>
BX Motherboard
PIII 550 Slot 1 Processor
384MB PC100 RAM
ATI graphics adapter
6.4GB Generic IDE Hard Drive (System disk)
20 GB Quantum Hard Drive (Programs disk)
40 GB Glyph X-project HardDrive (FireWire)
17" Monitor
No Network, No Internet.
Midiman USB 4x4
Creative 32x CDROM
M-Audio Delta TDIF with analog I/O and SP/DIF I/O
SoundBlaster Live with ASIO Drivers v 1.84
Tascam TM-D1000 Digital Mixer (All Cards I/O installed)
Mackie 1202 Analog Mixer
Yamaha NS-10's, Krk-KRock monitors
old Kawai K1
Yamaha DD50 trigger pads.
ART X-treme Pedal distortion plus effects
Digitech Vocalist EX.
Tascam MKIII cassete rec/player.
Good old electric and acoustic guitars.
Cubase 5.1
WaveLab 3.0
a bunch of Plugins
I use the Delta TDIF as the Recording card, the TM-D1000's effects are real good as well the dynamics, so I use both for my live recordings, the Pulsar is for all the extra processing and sound desing. It's important to say that the Delta TDIF is the master clock on my setup, thus the Pulsar II is the slave as well the TM-D1000, no problems so far.
I keep the Sblive in order to understand DSP, cause the new Drivers allow direct programming for the chip (emu10k1), I'm a software engineer so I want to lear that stuff, who knows,,may be some day I can program my own effects...
.<font size=-1>[ This Message was edited by: snoopy4ever on 2002-04-19 11:55 ]</font>
<font size=-1>[ This Message was edited by: snoopy4ever on 2002-04-19 11:55 ]</font>
plz creamware post this in your pulsar/scope page.
it's a way to rise your honesty and compatibility in the public!!
Go!!
so some pople don't have to buy a new PCto work happy with it, or just simply sell the creamware product.
it's a way to rise your honesty and compatibility in the public!!
Go!!
so some pople don't have to buy a new PCto work happy with it, or just simply sell the creamware product.
I'm still seeing new things in life.
<p><a href="http://mp3.com/dxl">www.mp3.com/dxl</a></p>
<p><a href="http://mp3.com/dxl">www.mp3.com/dxl</a></p>
Wow, who would have thought DXL would be the first person to not follow the format of this thread. Anyway.
We also have another setup running here, this one is a little bit more exotic. Note that quite a few people have not had the success we had, so I'm not sure I would recommend such a setup (definitely not if noise or heat are issues in your studio - even with quiet fans, they all run at full speed and this thing is literally a space heater):
4U Black 19" Rackmount Case
Tyan Tiger MP Dual Athlon (rev 1.03), AMD760MP chipset
2 x 1800MP AMD Processors
80gig 7200RPM Seagate Barracuda IV
Enermax 430watt Whisper w/ Fan Control (always running full speed)
Creamware Elektra+Pulsar1 (running Luna V3.01)
Windows XP Pro Dual ACPI
Subtest: 8 MasterVerbs (DSP limit)
Occasionally we have seen the "CopyProtection" error since the machine is running in ACPI mode, but very, very rarely, also closing this window and relaunching the Luna software usually works.
I will probably through in the SCOPE here and try the SFP beta, but this machine has actually been running really well for us.
Again, due to slightly trickier setup, and the fact nobody else seems to have this working as smoothly (I will say again, it will NOT work on a Tiger Rev1, it must be a rev3 (1.03) version board or you will get PCI issues - the rev1 Tiger has hardware problems with its bus), I can't say I suggest this system. It definitely does work well for us here though!
We also have another setup running here, this one is a little bit more exotic. Note that quite a few people have not had the success we had, so I'm not sure I would recommend such a setup (definitely not if noise or heat are issues in your studio - even with quiet fans, they all run at full speed and this thing is literally a space heater):
4U Black 19" Rackmount Case
Tyan Tiger MP Dual Athlon (rev 1.03), AMD760MP chipset
2 x 1800MP AMD Processors
80gig 7200RPM Seagate Barracuda IV
Enermax 430watt Whisper w/ Fan Control (always running full speed)
Creamware Elektra+Pulsar1 (running Luna V3.01)
Windows XP Pro Dual ACPI
Subtest: 8 MasterVerbs (DSP limit)
Occasionally we have seen the "CopyProtection" error since the machine is running in ACPI mode, but very, very rarely, also closing this window and relaunching the Luna software usually works.
I will probably through in the SCOPE here and try the SFP beta, but this machine has actually been running really well for us.
Again, due to slightly trickier setup, and the fact nobody else seems to have this working as smoothly (I will say again, it will NOT work on a Tiger Rev1, it must be a rev3 (1.03) version board or you will get PCI issues - the rev1 Tiger has hardware problems with its bus), I can't say I suggest this system. It definitely does work well for us here though!
Well... Right now I'm using... Stop that laugh now! Well, it is:
VB 610 V motherboard; soon heading for P4B266
Celeron 300 (clocked to 500); soon to be P4 2k
126 mb of nameless SDRAM; soon - 512 mb DDR
20.6 Gb IBM DTLA 5400 rpm hd; soon - Barracuda IV 80 Gb
Riva TNT 16 mb video; soon - GF4 64 MX-400(? - not defined yet)
15" Bridge monitor; soon - 19" LG Flatron.
Audio: Pulsar II Classic v 3.01 + STS-5000
Soon to add Luna II board for a little more DSP power.
MasterVerb test: 1 MasterVerb. Sometimes. If I beg my system on my knees and pray Teonanakatl instead of Meskalito.
Outboard: Korg N5ex.
Software:
LAP v4.8.1;
SONAR v1.3.1;
WaveLab 3.04d;
=]
<font size=-1>[ This Message was edited by: Noctulius on 2002-04-19 02:51 ]</font>
VB 610 V motherboard; soon heading for P4B266
Celeron 300 (clocked to 500); soon to be P4 2k
126 mb of nameless SDRAM; soon - 512 mb DDR
20.6 Gb IBM DTLA 5400 rpm hd; soon - Barracuda IV 80 Gb
Riva TNT 16 mb video; soon - GF4 64 MX-400(? - not defined yet)
15" Bridge monitor; soon - 19" LG Flatron.
Audio: Pulsar II Classic v 3.01 + STS-5000
Soon to add Luna II board for a little more DSP power.
MasterVerb test: 1 MasterVerb. Sometimes. If I beg my system on my knees and pray Teonanakatl instead of Meskalito.
Outboard: Korg N5ex.
Software:
LAP v4.8.1;
SONAR v1.3.1;
WaveLab 3.04d;
=]
<font size=-1>[ This Message was edited by: Noctulius on 2002-04-19 02:51 ]</font>
-
Rob van Berkel
- Posts: 236
- Joined: Sun Jul 29, 2001 4:00 pm
- Location: Rotterdam, The Netherlands
MSI Big tower, 1x12cm, 1x9cm, 2x8c, fans
Abit TH7-II w/o RAID i850 Motherboard
1.7Ghz Pentium 4
512meg (4x128) Dane-Elec (NEC) PC800 RDRAM
IDE-1 master: 60G 7200rpm Barracuda (system)
IDE-1 slave: 80G 7200rpm Barracuda (audio/data)
IDE-2 master: Aopen 52x CDR
IDE-2 slave: HP9310i CDRW
Asus V7700 GeForce2 32meg
19" ViewSonic Monitor @ 1280x1024x32@85
350 watt SilentSystems Power Supply
Win98SE Lite - tweaked and optimized
2 x Pulsar2 (running Pulsar V3.01b)
1 x Yamaha SW1000 XG + PLG150-AN
Logic Audio Gold 4.8.1 (just oredered LAG 5)
FruityLoops 3.4
SubMasterVerbTest - see <A HREF="http://www.berkel.net/mv.gif" TARGET="_blank">here</A> (at
default BIOS settings)
External: Roland PC300-MK2 midi keyboard
Mindprint DiPort AD/DA convertor 24bit/48kHz
Everything runs flawless
Abit TH7-II w/o RAID i850 Motherboard
1.7Ghz Pentium 4
512meg (4x128) Dane-Elec (NEC) PC800 RDRAM
IDE-1 master: 60G 7200rpm Barracuda (system)
IDE-1 slave: 80G 7200rpm Barracuda (audio/data)
IDE-2 master: Aopen 52x CDR
IDE-2 slave: HP9310i CDRW
Asus V7700 GeForce2 32meg
19" ViewSonic Monitor @ 1280x1024x32@85
350 watt SilentSystems Power Supply
Win98SE Lite - tweaked and optimized
2 x Pulsar2 (running Pulsar V3.01b)
1 x Yamaha SW1000 XG + PLG150-AN
Logic Audio Gold 4.8.1 (just oredered LAG 5)
FruityLoops 3.4
SubMasterVerbTest - see <A HREF="http://www.berkel.net/mv.gif" TARGET="_blank">here</A> (at
default BIOS settings)
External: Roland PC300-MK2 midi keyboard
Mindprint DiPort AD/DA convertor 24bit/48kHz
Everything runs flawless
-
kensuguro
- Posts: 4434
- Joined: Sun Jul 08, 2001 4:00 pm
- Location: BPM 60 to somewhere around 150
- Contact:
This seems like a fun party going on. Here's my setup:
Asus P4TE with onboard audio
2Ghz P4
512(256X2) noname RAM
20Gb IBM IDE, they're all IDE
80Gb Maxtor
100Gb Wester Digital(for backups)
ELSA Gladiac GeForce2 GTS
19" EIZO 54Ts
TOSHIBA DVD+CDR
370watt powersuplly.. (if I remember)
WinXP
Pulsar II on OS 3.01
YAMAHA DSP Factory with c-console 1.4
SB Live for Nord Mod control
verbtest: 8(dsp limit)
Software:
Samplitude, Nuendo, cooledit,
etc. etc. the usual bunch. I don't use Gigasampler tho, for no reason.
I use Triton as sequencer cuz I'm just so used to it.
Hardware gear: Triton, Trinity, Nord Mod, Nord Electro 73, Yamaha QY (this guy's cute), a pair of cheap congas, a djembe (that I hit with a stick), a bunch of Chinese instruments, and a cellphone. Oh yeah, a SHURE Beta 58a and Focusrite Vocalmaster.
Have a look!
Yup, it's waay too messy for anyone serious. But I'm getting ready to move the setup to a different location so what the hell. See that TV behind the monitor? That's got to be atleast as old as I am!
<font size=-1>[ This Message was edited by: kensuguro on 2002-04-26 04:39 ]</font>
<font size=-1>[ This Message was edited by: kensuguro on 2002-04-26 04:40 ]</font>
Asus P4TE with onboard audio
2Ghz P4
512(256X2) noname RAM
20Gb IBM IDE, they're all IDE
80Gb Maxtor
100Gb Wester Digital(for backups)
ELSA Gladiac GeForce2 GTS
19" EIZO 54Ts
TOSHIBA DVD+CDR
370watt powersuplly.. (if I remember)
WinXP
Pulsar II on OS 3.01
YAMAHA DSP Factory with c-console 1.4
SB Live for Nord Mod control
verbtest: 8(dsp limit)
Software:
Samplitude, Nuendo, cooledit,
etc. etc. the usual bunch. I don't use Gigasampler tho, for no reason.
I use Triton as sequencer cuz I'm just so used to it.
Hardware gear: Triton, Trinity, Nord Mod, Nord Electro 73, Yamaha QY (this guy's cute), a pair of cheap congas, a djembe (that I hit with a stick), a bunch of Chinese instruments, and a cellphone. Oh yeah, a SHURE Beta 58a and Focusrite Vocalmaster.
Have a look!
Yup, it's waay too messy for anyone serious. But I'm getting ready to move the setup to a different location so what the hell.
See that TV behind the monitor? That's got to be atleast as old as I am!<font size=-1>[ This Message was edited by: kensuguro on 2002-04-26 04:39 ]</font>
<font size=-1>[ This Message was edited by: kensuguro on 2002-04-26 04:40 ]</font>
Ok, NO photo of my ultra-messy workspace.
System:
Win98SE
Pulsar 3.01b
Intel Celeron 1200 FCPGA2
3x128MB Infineon PC-100 (selected)
Asus TUSL2-C
Zalman 300W ultrasilent PSU
Ati Radeon VE dualhead
2 additional Papst fans, one for the DSPs, one for better airflow
ADI microscan 6P 19" (1600x1200) and Sony 15" sf2 (1280x1024)
Pulsar 2 classic I/O
Powerpulsar classic I/O
Adaptec 29160 SCSI
27GB Maxtor IDE (System, programs, i-net stuff, a few games)
30GB Maxtor IDE (music, pictures, videos, backup of some audiodata and some programs)
2x18GB Seagate Cheetah 10k rpm SCSI external (audiodata only; tracking, sampling, mastering)
Samsung DVD and Samsung CD-RW, both IDE
2xA16 (old)
Midex8
Level One USB ethernet adapter
fanatec C&C Edition Trackball (the one with the lights inside)
Midi input devices:
Yamaha CBX-K2 Midi keyboard
Roland Octapad2 (PAD-80)
Axon NGC-66 neural guitar-to-midi converter
Monitoring:
2x Quested F11
1x Quested VS1112
Behringer 602a
...and some outboard gear of course;
mics, FX, synths, dynamics, tube preamp...
and a nice DAT porty with an even nicer stereo mic (soundman OKM2) for sample-hunting.
Now, what I REALLY lack is a place to work, a studio room. The one that I was close to get suddenly became unreachable (the owner decided to not let it for rent anymore but use it himself instead)
ah, what I forgot to mention:
System run´s very good, "Subtest" gives me 12 MVs max, up to 9 will make no big difference in overall performance, and the 13th will finally slow it all down to zero. But no PCI-overflow messages at all, never seen on this MoBo!
<font size=-1>[ This Message was edited by: JoeKa on 2002-04-26 10:15 ]</font>
System:
Win98SE
Pulsar 3.01b
Intel Celeron 1200 FCPGA2
3x128MB Infineon PC-100 (selected)
Asus TUSL2-C
Zalman 300W ultrasilent PSU
Ati Radeon VE dualhead
2 additional Papst fans, one for the DSPs, one for better airflow
ADI microscan 6P 19" (1600x1200) and Sony 15" sf2 (1280x1024)
Pulsar 2 classic I/O
Powerpulsar classic I/O
Adaptec 29160 SCSI
27GB Maxtor IDE (System, programs, i-net stuff, a few games)
30GB Maxtor IDE (music, pictures, videos, backup of some audiodata and some programs)
2x18GB Seagate Cheetah 10k rpm SCSI external (audiodata only; tracking, sampling, mastering)
Samsung DVD and Samsung CD-RW, both IDE
2xA16 (old)
Midex8
Level One USB ethernet adapter
fanatec C&C Edition Trackball (the one with the lights inside)
Midi input devices:
Yamaha CBX-K2 Midi keyboard
Roland Octapad2 (PAD-80)
Axon NGC-66 neural guitar-to-midi converter
Monitoring:
2x Quested F11
1x Quested VS1112
Behringer 602a
...and some outboard gear of course;
mics, FX, synths, dynamics, tube preamp...
and a nice DAT porty with an even nicer stereo mic (soundman OKM2) for sample-hunting.
Now, what I REALLY lack is a place to work, a studio room. The one that I was close to get suddenly became unreachable (the owner decided to not let it for rent anymore but use it himself instead)
ah, what I forgot to mention:
System run´s very good, "Subtest" gives me 12 MVs max, up to 9 will make no big difference in overall performance, and the 13th will finally slow it all down to zero. But no PCI-overflow messages at all, never seen on this MoBo!
<font size=-1>[ This Message was edited by: JoeKa on 2002-04-26 10:15 ]</font>
Thought I would contribute to the Mac side of things....this setup works flawlessly....no problems on installation and no crashes:
Powermac G4 500mhz
768mb RAM
20GIG System HD
40GIG 7200 RPM Audio HD
OS 9.2.2
Pulsar II (Soon to add an SRB!) Slaved clock
Digidesign Digi 001 system (Connected to Pulsar via Lightpipe) Slaved clock
Pro Tools le 5.1.1
Adaptec SCSI controller card.
NEC 1700M+ LCD monitor
Apogee Rosetta A/D (Serves as master clock for system, connected to 001 via SPDIF.
TC Electronic M-One
Opcode Studio 4 8x8 MIDI interface
OMS 2.3.8
Roland PC-300 USB Keyboard (serves as master keyboard)
Reason
Dynamo
Battery
ReCycle 2.0
RTAS Plugs for Pro Tools:
Waves 3.0 Gold bundle
Bombfactory LA-2A, 1176, Fairchild, Joemeek, Pultec EQ
Metric Halo Channelstrip
Maxim
McDsp Compressorbank, Filterbank, and Analog Channel
Orange Vocoder
Kind of Loud RealVerb
GRM
Cheers
<font size=-1>[ This Message was edited by: Kamurah on 2002-05-22 22:30 ]</font>
Powermac G4 500mhz
768mb RAM
20GIG System HD
40GIG 7200 RPM Audio HD
OS 9.2.2
Pulsar II (Soon to add an SRB!) Slaved clock
Digidesign Digi 001 system (Connected to Pulsar via Lightpipe) Slaved clock
Pro Tools le 5.1.1
Adaptec SCSI controller card.
NEC 1700M+ LCD monitor
Apogee Rosetta A/D (Serves as master clock for system, connected to 001 via SPDIF.
TC Electronic M-One
Opcode Studio 4 8x8 MIDI interface
OMS 2.3.8
Roland PC-300 USB Keyboard (serves as master keyboard)
Reason
Dynamo
Battery
ReCycle 2.0
RTAS Plugs for Pro Tools:
Waves 3.0 Gold bundle
Bombfactory LA-2A, 1176, Fairchild, Joemeek, Pultec EQ
Metric Halo Channelstrip
Maxim
McDsp Compressorbank, Filterbank, and Analog Channel
Orange Vocoder
Kind of Loud RealVerb
GRM
Cheers
<font size=-1>[ This Message was edited by: Kamurah on 2002-05-22 22:30 ]</font>
uploaded pic, in my user setup.
its nice and green, and i have a few planties (only can see the lucky bamboo). and an orange seat which looks like the dogs got after it...hehe.
its rather boring looking outside my windows, but i think it is very important for myself at least...to be facing them.
when i wasn't prior to it, just felt like i was staring into a void...even more isolated than i ought to feel. at the very least in view of some.
thought of something for the mac users that is rather important.
extension sets.
i can't be bothered to list mine now, but you know...anyhow i don't have any conflicts. though i do run as lean as i can get away with.
its nice and green, and i have a few planties (only can see the lucky bamboo). and an orange seat which looks like the dogs got after it...hehe.
its rather boring looking outside my windows, but i think it is very important for myself at least...to be facing them.
when i wasn't prior to it, just felt like i was staring into a void...even more isolated than i ought to feel. at the very least in view of some.
thought of something for the mac users that is rather important.
extension sets.
i can't be bothered to list mine now, but you know...anyhow i don't have any conflicts. though i do run as lean as i can get away with.
-
algorhythm
- Posts: 1139
- Joined: Tue Apr 03, 2001 4:00 pm
- Location: Tennessee, USA
- Contact:
Computer Hardware:
Pretty "classic" Pulsar setup - never bothered to run the masterverb test - never had a PCI overflow problem before either
Pentium III 933mhz - 512MB PC133 RAM - ASUS CUSL2-C mainboard
Matrox G450 video card - 17" & 15" monitors
Midnight Blue server case from infinitevortex
Creamware Pulsar I - Creamware Luna II soundcards
Software:
Operating System > Micro$oft Windows XP
Studio Integration Software > Creamware Pulsar 3.01
Sequencers > Cubase VST 5 - Acid 3
Audio Editors > Sound Forge 5 - Recycle 2
Software Synthesizers and Effects > too many to list
Hardware Equipment:
Mixer: Fostex VM200
Monitors: Event 20/20 BAS
Drum Machines: Korg ES-1 - Korg ER-1
Synthesizers: Yamaha CS2X - Korg EA-1
Effects Processors: Electrix FilterQueen - MOFX - EQ Killer - Korg KM-1
_________________
<font size="-1">algorhythm</algorhythm</font><br><font size="-2">get the 411</font></p>
<font size=-1>[ This Message was edited by: algorhythm on 2002-05-19 19:46 ]</font>
Pretty "classic" Pulsar setup - never bothered to run the masterverb test - never had a PCI overflow problem before either
Pentium III 933mhz - 512MB PC133 RAM - ASUS CUSL2-C mainboard
Matrox G450 video card - 17" & 15" monitors
Midnight Blue server case from infinitevortex
Creamware Pulsar I - Creamware Luna II soundcards
Software:
Operating System > Micro$oft Windows XP
Studio Integration Software > Creamware Pulsar 3.01
Sequencers > Cubase VST 5 - Acid 3
Audio Editors > Sound Forge 5 - Recycle 2
Software Synthesizers and Effects > too many to list
Hardware Equipment:
Mixer: Fostex VM200
Monitors: Event 20/20 BAS
Drum Machines: Korg ES-1 - Korg ER-1
Synthesizers: Yamaha CS2X - Korg EA-1
Effects Processors: Electrix FilterQueen - MOFX - EQ Killer - Korg KM-1
_________________
<font size="-1">algorhythm</algorhythm</font><br><font size="-2">get the 411</font></p>
<font size=-1>[ This Message was edited by: algorhythm on 2002-05-19 19:46 ]</font>
5U 19" IPC-5101 server case
ASUS P4TE i850 Motherboard
2.2Ghz Pentium 4
1024meg (4x256) - PC800 Kingmax
123gb 7200RPM IBM Deskstar IPC-5101
30gb IBM
19" V7 - n96dn monitor
Hercules Prophet (nvidia 2)
52x sony cd
12x plextor writer
431w EG465P-V DualFan Gold
WinXP (tweaked)
Pulsar2+
adat xt
SFP
Cubase/wavelab
_________________
<font size=-2>got my mojo working, but it just won't work on you</font>
<font size=-1>[ This Message was edited by: sandrob on 2002-05-20 00:04 ]</font>
ASUS P4TE i850 Motherboard
2.2Ghz Pentium 4
1024meg (4x256) - PC800 Kingmax
123gb 7200RPM IBM Deskstar IPC-5101
30gb IBM
19" V7 - n96dn monitor
Hercules Prophet (nvidia 2)
52x sony cd
12x plextor writer
431w EG465P-V DualFan Gold
WinXP (tweaked)
Pulsar2+
adat xt
SFP
Cubase/wavelab
_________________
<font size=-2>got my mojo working, but it just won't work on you</font>
<font size=-1>[ This Message was edited by: sandrob on 2002-05-20 00:04 ]</font>
Asus cusl2-C
P3 866
384 MB Ram 133Mhz
Matrox G200 AGP with external video acquisition box (cool!)
pulsar 1 + luna 2, running SFP
HD 80GB 7200rpm
HD 6GB
HD 20GB 7200 rpm
6 total partition: 2 for operating systems ("normal" and "audio" settings, the audio settings has no internet, no useless progs)
1 for all data, 1 for cakewalk9 wavedata, 1 for samples and SFP programs, 1 for general storage. i use norton ghost for backup the system partitions.
17'' monitor
a SB Live i use for mp3 and CD listening and for videos viewing...
my gear (just for saying it...)
1 mute keyboard - flowers - 46 keys
yamaha Pacifica guitar with a POD 2.3
midicontroller built by myself (www.ucapps.de)
breath controller built by myself (same link)
guitar synth GR-1 with a dedicated guitar with esafonic pickup.
Korg 03RW
Alesis DM5
Fostex VC8 Analog/adat converter
Presonus TubePre
Roytek mic
original samples CDs: advanced orchestra compact edition, classical choir, bob clearmountain drums II, Will Lee bass library
i own also sitar (!), an el-cheapo violin (which i'm NOT able to play!), some flutes and a small zither
i'm just an amateur musician (a bit deaf), you can listen to my music and see some other photos at
http://alchemyoflife.cjb.net
i run cakewalk9
<font size=-1>[ This Message was edited by: bosone on 2003-03-14 03:20 ]</font>
P3 866
384 MB Ram 133Mhz
Matrox G200 AGP with external video acquisition box (cool!)
pulsar 1 + luna 2, running SFP
HD 80GB 7200rpm
HD 6GB
HD 20GB 7200 rpm
6 total partition: 2 for operating systems ("normal" and "audio" settings, the audio settings has no internet, no useless progs)
1 for all data, 1 for cakewalk9 wavedata, 1 for samples and SFP programs, 1 for general storage. i use norton ghost for backup the system partitions.
17'' monitor
a SB Live i use for mp3 and CD listening and for videos viewing...
my gear (just for saying it...)
1 mute keyboard - flowers - 46 keys
yamaha Pacifica guitar with a POD 2.3
midicontroller built by myself (www.ucapps.de)
breath controller built by myself (same link)
guitar synth GR-1 with a dedicated guitar with esafonic pickup.
Korg 03RW
Alesis DM5
Fostex VC8 Analog/adat converter
Presonus TubePre
Roytek mic
original samples CDs: advanced orchestra compact edition, classical choir, bob clearmountain drums II, Will Lee bass library
i own also sitar (!), an el-cheapo violin (which i'm NOT able to play!), some flutes and a small zither
i'm just an amateur musician (a bit deaf), you can listen to my music and see some other photos at
http://alchemyoflife.cjb.net
i run cakewalk9
<font size=-1>[ This Message was edited by: bosone on 2003-03-14 03:20 ]</font>
Computer:
Asus P4T-E mobo
1.8 P4 Northwood (clocked @ 2.0)
512mb rdram
30 gig Baracuda (system drive)
60 gig Baracuda (audio Drive)
40 gig Baracuda (EXs24 Storage)
Matrox G550 AGP card
Pulsar II (PCI slot 2)
Silent drive enclosures for both drives
Silent 350watt power supply
Silent processor/case fans
Software:
Windows XP Pro (full on audio tweakidge)
Scope Fusion 3.1c
Logic Audio Platinum 5.5
Hardware:
Roland Juno Alpha-1
novation supernova II
Novation Remote 25
korg trinity
korg 880 A/D
Otari DAT
midiman usb midisport 4x4
midiman CO2 coax to optical converter
Behringer composer pro
behringer ultrapatch pro
mackie 1202 mixing desk
phat-boy midi controller
Samson servo-170 amp
Yamaha NS-10M
sennheiser HD-25 cans
18" NEC LCD 1860nx (Superb - Highly Recomend)
very stable.
<font size=-1>[ This Message was edited by: mgranger on 2003-10-10 09:34 ]</font>
<font size=-1>[ This Message was edited by: mgranger on 2003-12-23 15:51 ]</font>
Asus P4T-E mobo
1.8 P4 Northwood (clocked @ 2.0)
512mb rdram
30 gig Baracuda (system drive)
60 gig Baracuda (audio Drive)
40 gig Baracuda (EXs24 Storage)
Matrox G550 AGP card
Pulsar II (PCI slot 2)
Silent drive enclosures for both drives
Silent 350watt power supply
Silent processor/case fans
Software:
Windows XP Pro (full on audio tweakidge)
Scope Fusion 3.1c
Logic Audio Platinum 5.5
Hardware:
Roland Juno Alpha-1
novation supernova II
Novation Remote 25
korg trinity
korg 880 A/D
Otari DAT
midiman usb midisport 4x4
midiman CO2 coax to optical converter
Behringer composer pro
behringer ultrapatch pro
mackie 1202 mixing desk
phat-boy midi controller
Samson servo-170 amp
Yamaha NS-10M
sennheiser HD-25 cans
18" NEC LCD 1860nx (Superb - Highly Recomend)
very stable.
<font size=-1>[ This Message was edited by: mgranger on 2003-10-10 09:34 ]</font>
<font size=-1>[ This Message was edited by: mgranger on 2003-12-23 15:51 ]</font>