dynatube announced

katano · Post by **katano** » Sat Apr 15, 2006 10:04 am

On 2006-04-15 10:59, SpaceBlues wrote:
Has anyone had time to test Dynatube, and If so, what´s the verdict

I'm not a guitarist. i'll test dynatube tomorrow with my brother, he plays guitar very well and has some years experience with different guitars and amps. i'll post a little review on this place...

cheerz

SpaceBlues · Post by **SpaceBlues** » Sat Apr 15, 2006 10:09 am

On 2006-04-15 11:04, katano wrote:
On 2006-04-15 10:59, SpaceBlues wrote:
Has anyone had time to test Dynatube, and If so, what´s the verdict
I'm not a guitarist. i'll test dynatube tomorrow with my brother, he plays guitar very well and has some years experience with different guitars and amps. i'll post a little review on this place...

cheerz

I´m looking forward to that.

jea · Post by **jea** » Sat Apr 15, 2006 11:26 am

Anyone tested it yet?

Does it work in XTC?

jea · Post by **jea** » Sun Apr 16, 2006 3:20 am

Just bought it.

It works in XTC.

erminardi · Post by **erminardi** » Sun Apr 16, 2006 4:09 am

On 2006-04-16 04:20, jea wrote:
Just bought it.

It works in XTC.

Jea, do you can describe (if U have the bundle...) to us the features of Vinco DT??? It's a cutted version of original one or what?
Thanks in advance.

jea · Post by **jea** » Sun Apr 16, 2006 5:10 am

Hi again,

Vinco DT appears to me as a cutdown version.

I did not pass any audio thru it, I am building the racks atm, so no speakers connected

But it appears to me that some details is left out, as the "VU" meters is not there, just peakmeters etc.

Back to building ....

breitner · Post by **breitner** » Sun Apr 16, 2006 11:29 am

On 2006-04-16 06:10, jea wrote:
Hi again,

Vinco DT appears to me as a cutdown version.

I did not pass any audio thru it, I am building the racks atm, so no speakers connected

But it appears to me that some details is left out, as the "VU" meters is not there, just peakmeters etc.

Back to building ....

Just purchased and installed the DT set. Preamp set up still needs tweaking but the results are already becoming clear: excellent set of soundtools. The Vinco DT is a tiny version of the Vinco. Just two knobs and a button (soft clip)
ONE NEGATIVE (IMHO unforgivable and to be mended asap) Where is the MIDI Control?

Jonathan T · Post by **Jonathan T** » Sun Apr 16, 2006 11:43 am

I tried the direct FTP link in the email I received after purchasing and like others on here it didn't work for me.

However the generate/download procedure was successful in my case, so if you haven't done so try going to your page on the Creamware site and then on to your downloads section.

Regards

Jonathan

virtualstudio · Post by **virtualstudio** » Sun Apr 16, 2006 1:51 pm

ok I have it, but I'm not smiling yet.

the only speakercabinet that seems to work is the MB: so only if I put the FT JM VX on top off the mesaboogie cabinet I have sound.

katano · Post by **katano** » Sun Apr 16, 2006 5:15 pm

On 2006-04-16 14:51, virtualstudio wrote:
ok I have it, but I'm not smiling yet.

the only speakercabinet that seems to work is the MB: so only if I put the FT JM VX on top off the mesaboogie cabinet I have sound.

hey virtualstudio...

i was in my studio this afternoon for some first steps with dynatube. all cabs and all amps in every combination worked fine for me...

Shroomz~> · Post by **Shroomz~>** » Mon Apr 17, 2006 4:37 am

Do these amp & speaker cab sim's have full midi control of all parameters or not?

Shroomz~> · Post by **Shroomz~>** » Mon Apr 17, 2006 4:47 am

Just read the specs & all parameters should be controllable via midi. Are they then?

dbmac · Post by **dbmac** » Mon Apr 17, 2006 4:56 am

Shroomz~> · Post by **Shroomz~>** » Mon Apr 17, 2006 5:32 am

That's a pisser. None at all?

breitner · Post by **breitner** » Mon Apr 17, 2006 7:21 am

No, no midi controls yet, very strange indeed and a major setback. CW promised us that we could 'screw around', if the specs say that there is midi control, they should fix it asap or instruct us how to install it.

breitner · Post by **breitner** » Mon Apr 17, 2006 7:26 am

BTW: I connected my Behringer GX210 (nice amp for clean sounds, good speakers, but lousy on the effects and distortion). This combo has an insert loop. I run that through the DT's and it screams and rocks like never before.

Shroomz~> · Post by **Shroomz~>** » Mon Apr 17, 2006 7:54 am

The mind truely boggles. It clearly states in the 'specifications' sections on the Dynatube website that all parameters are controlable via midi. I like throwing the odd drum channel thru an amp & cab sim & tweaking parameters via midi. For me, this is definately a complete show-stopper if there's really no midi control on Dynatube.

Shroomz~> · Post by **Shroomz~>** » Mon Apr 17, 2006 7:56 am

And before anyone says it... I know the original amps & cabs didn't have midi control, but that ain't the point at all.

Mr Arkadin · Post by **Mr Arkadin** » Mon Apr 17, 2006 10:29 am

Before jumping to too many conclusions about MIDI (or lack thereof), check bosone's thread.

dbmac · Post by **dbmac** » Mon Apr 17, 2006 12:15 pm

Yup, Bosone is right - the CC assignments show up when the Dynatube is an insert.

/dave