PlanetZ forums - scopeusers.com

Where is the website information on this Flextor III?
Where to buy and download?

Thanks

try Bidule (Standalone).. This might help to load VST effects without host application in (almost) real time.

www.plogue.com

So this means it isn't release yet..

I'm waiting to see it release

I've search through their Adern Flexor website, but can't find where to download Adern Flexor 2. It just has Flexor 1.5 only.

Anyone can help me direct to the download link?

Thank you.

I run Vista with Nuendo 3 and on-board audio ASIO (no Vista driver for Scope to play ASIO now). I installed Drums VSTi from DFH, Piano from The Grand 2 and also tons of VST effects. I can feel the speed of loading very large VSTi (drums, piano). It seems faster and faster everyday I used Vista. You ...

Hi musurgio

Have you tried increase attack time to be around > 20ms? And may be try it in RMS mode with ratio at 20.

Just wanna know how these setting change the very low end respond..


PS. The compressor are true to affect the dynamics, but it also has 'Character' for its own compression, which ...

hubird, how old are you?!?

I see no reason why someone has to always bite someone all over this webboard. Sorry to say sir.. but it's too much.. I'm tired of reading the 'bite' which has nothing to do with the context..

I try live kik drums on both vinco and compressorX but I prefer vinco sound. Because it's bigger and more juicy sound than compressorX.

But for the Vinco, I mostly use RMS mode all times.. It's more natural sound to my ears, unless I want to pump the sound.

Just my thought..

Seem the workaround is not possible to make ASIO driver be seen by Vista.

No ASIO possible..

Anymore workaround to make ASIO usable in VISTA?

Hi Warp,

I already bought your Plate & Ambience for Scope. It has the very expensive sound. =)

One question, I doubt what you said. You mean the Scope Device can be hacked to see the algorithm inside the device?

About cable..., when you config your A16 Ultra right, use balanced cable for balanced operation.., and use unbalanced cable for unbalanced operation..

Or easier, you can use all balanced cable but change only head of the plugs. Use balanced 1/4 phone jack for balanced operation and use unbalanced 1 ...

The good thing of A16 Ultra is they accept both balance and unbalance signal in bank of 8. There is a little jumper at the back of the unit for this special setup. This means you can record balanced signal to input of A16 Ultra and output to unbalanced mixer or vice versa without any problem. Try to ...

Also, one thing..

Make sure that you select 'ASIO Scope' as the audio hardware option in your sequensor.

That should do the job, and you don't have to daydreaming waiting for someone to help.. =)

You already have what you need to install XTC mode. The easy way to do is reintall the scope 4.0 AFTER you install the sequensor software (like logic or nuendo). Then the installer should detect themself where the VSTPLUGINS folder is..

Then after install, open 'setting' page and make sure you ...

I have my Pulsar II card to slave word clock from Apogee PSX-100 via word clock option for Pulsar since a few years ago. And it really make things sound better...

I think it's important to have the best as possible one digital clock master in digital workstation.. It really worth..

On 2005-11-04 02:19, virtualstudio wrote:
hi,
I don't know about focusrite, but can't you set your Scope to master?
for me that works the best.

goodluck


If the input is done in analog, then it's no problem to set scope to Master. But if you want to record Digital from Octopre, then it's ...

I'm sure that STM2448 and STM4896 are better sounding and have more dynamic than STM1632.., especially summing bus.. And if you use "Phrase Comensation" in the STM1632, it seems that the sound is narrower. (which is not happen in STM2448 & STM 4896)

1. Make sure you connect the ADAT output of Octapre (has red light) to the input of ADAT A of your pulsar (has NO red light).

2. Make sure the Octapre is in Master clock (not slave word clock).

3. Make sure that the "ADAT Opt" is chosen, not "SPDIF Opt", in sample rate setting..

Sorry to say...

The VDAT does sound different from ASIO... Yes it DOES different. It is not from Scope Mixer that makes sound different. Try play same master audio file through 1. Logic, 2. Samplitude, 3. Wavelab, 4. VDAT (all use ASIA driver to the same Scope Mixer -except VDAT that route to the ...

Oh no...

I'm sorry to make it confusing. As I said before about "DAE" in Logic Audio. Digidesign Protools HD make their hardware FULLY compatible with Logic Audio Platinum via "DAE" (Digidesign Audio Engine). Because Logic Audio is widely used all over the professional world for arrange, compose ...